Home / Platform / Wired devices
Wired devices, pre-configured before they reach site
Servers, controllers, I/O modules, room devices, lighting and metering, from one catalogue. Every device arrives QR-coded and pre-configured from the digital twin, so your certified partner's electricians install it with the Installer App, with no laptop at the panel.
Where each device sits
From the internet down to the field bus: the Bisly Server with the Bisly router and PoE switches in the rack; a Bisly Controller 8 panel per floor, a Bisly Mini Server in each plant room, the Bisly DALI Bridge 2 and the Bisly M-Bus Gateway 250; the Bisly Room Controller 4, presence sensors, I/O modules and the Bisly AC Gateway 1 in the rooms; third-party plant connected by protocol below them.
From the top: bisly.cloud and the Installer App; the Bisly Server, router and switches, Bisly Hub, Mini Server, DALI Bridge 2 and M-Bus Gateway 250 on the automation LAN; Controller 8, base station and I/O modules; room devices on the field buses; third-party plant below.
Catalogue
Every device from the Bisly Commercial Catalogue 2026/27, with its role and key specifications. Click a card for the full specification; datasheets and EU declarations of conformity are on the Documents page.
Bisly Server CX00
The on-site brain of a commercial building: central management of automation, real-time coordination of HVAC, lighting, access and energy, on a dedicated local network with secure cloud connectivity. Logic, schedules and control loops keep running through internet outages and resync when the connection returns.
Key specifications
Bisly Mini Server CX01
Runs a sub-system on its own: a heating substation, a ventilation plant room, a detached building or a whole small site. Logic and trends run locally; the Bisly Server and the cloud supervise. One product from a single small building to the plant room of a 20,000 m² office.
Key specifications
Bisly Controller 8 CU08
The standard automation station of a Bisly commercial building: 8 power relay outputs, universal I/O, three RS-485 Modbus ports and 1-Wire sensing on a DIN rail. One panel per floor or general-area zone runs heating manifolds, lighting groups, door locks, room-controller trunks and floor I/O.
Key specifications
Bisly Analog Input 8 IA08
Eight analog inputs for the sensors plant and floor control depend on: duct and pipe temperatures, pressures, CO₂ and humidity transmitters, valve and damper feedback. Each channel is set in the digital twin.
Key specifications
Bisly Analog Output 8 IQ08
Eight 0-10 V outputs for valves, dampers, fan-coil fans and variable-speed drives where no factory controller exists: mixing circuits, VAV boxes, extract fans, de-icing and auxiliary circuits.
Key specifications
Bisly Relay Module 8 IR08
Eight 10 A relays and 8 isolated digital inputs in one DIN-rail module: pumps, contactors, door locks, extract fans and interlocks on the outputs, status contacts, flow switches and frost stats on the inputs.
Key specifications
Bisly AC Gateway 1 GA01
Integrates split, multi-split and VRF / VRV indoor units into the Bisly system: setpoints, modes, fan speeds and fault states, per room, on the same platform as everything else. The unit needs no wired thermostat of its own.
Key specifications
Bisly M-Bus Gateway 250 GM250
A Bisly-managed IP metering master for wired and wireless meter networks in one device: 250 unit loads of wired M-Bus with automatic discovery, plus an integrated wireless M-Bus (OMS) receiver for meters and heat-cost allocators where no cabling exists.
Key specifications
Bisly Room Controller 4 RC04
A glass-front touch controller with sensing and control outputs in one flush unit. It measures the room, shows the tenant the setpoint and drives the fan-coil or heating actuators directly, following schedules and setpoints from the Bisly Server.
Key specifications
Bisly Hub RP10
A PoE-powered 10.1-inch wall panel for receptions, meeting rooms, floor lobbies and apartments: lighting, climate, access, intercom and security in one interface, the same as the Bisly app.
Key specifications
Bisly DALI Bridge 2 LD02
The Ethernet DALI-2 application controller for a floor's lighting: one DALI-2 line of 64 control gears with bus power on board, colour-capable drivers, presence and lux sensors on the same line. Schedules keep running on its built-in clock.
Key specifications
Bisly DALI Input 4 LI04-D2
A DALI-2 bus-powered input coupler that brings 4 ordinary push buttons or dry contacts onto the DALI-2 line. It fits in the wall box behind the existing switch and needs no mains input.
Key specifications
Bisly Presence Sensor SP01-D2
DALI-2 presence and lux sensing for lighting automation: presence detection, daylight harvesting and constant-light control on the DALI line, bus powered, commissioned by scan. The microwave detector sees small movements at a desk.
Key specifications
Bisly Presence Sensor High-bay SP02-D2
The high-bay variant for halls, gyms, warehouses and loading areas: PIR presence with wide-angle optics for mounting heights up to 10 m, lux sensing for daylight control.
Key specifications
Access control readers HID · Hikvision · Inception
Doors, gates and lifts open for the right people at the right times, and every event is logged in the same BMS. HID Signo readers with cards, NFC, mobile credentials and PIN over encrypted OSDP; locks switched from Bisly relays.
Key specifications
Intercoms 2N · Hikvision
Visitors call from the door; staff or tenants answer on the phone or the Bisly Hub and release the door. Directory, PIN, QR and fingerprint entry run from the same door station.
Key specifications
IP cameras Hikvision · Bosch · Hanwha · LTS
Live video in the same screen as access events and alarms, across the portfolio, without a separate video system. ANPR cameras open gates and parking by number plate.
Key specifications
Bisly router and PoE switches Ubiquiti
The automation runs on its own network, so it never conflicts with tenant or office IT. A pre-configured Bisly router creates the isolated automation LAN; managed PoE switches feed panels, DALI bridges, readers, intercoms, cameras and the Bisly Hub.
Key specifications
No devices in this group.
Quick device setup with a phone: scan-to-connect with the Installer App
Devices arrive QR-coded and pre-configured by your partner in the Bisly platform. The Installer App walks the electrician through each panel and room; the scan matches the serial with the pre-configured device, and every controller is tested before the installer leaves the room.
For certified partners and their electricians.
Get a quote from the digital twin
Send us your building and we return a bill of materials, a panel layout and a fixed price from the Sales Configurator, with no engineering hours in it.
A 30-minute discovery call. Scope and a fixed price within 5 working days.